Slow Car Fast
THE MG
January 7, 2010 - Dumb.
Remember my trip to the junkyard to pick up some Rabbit fenders so I could scavenge the arches? At the time, I thought the rears might actually work pretty well but the yard wanted a pile of money for them.
Well, it turns out you can get patch panels to repair Rabbits. New front fenders are available from JC Whitney and others, but even better Rabbitparts.com carries a rear arch repair panel that's exactly what I need. They're only $48 each and brand new steel. I'm going to pick up a pair to see how they work, and I may end up ordering another pair to replace what I have if the shape looks a bit better.
Yeesh. Never thought to check before.
entry 249 - tags: body
January 10, 2010 - It was a day of fabrication.
I spent the whole day cutting weird shapes out of cardboard, duplicating them in steel and then welding them in. The stock inner fender sheetmetal is fairly thin, so it takes a certain amount of finesse not to burn through it.
I finished up the shock tower on the passenger's side, and I'm happier with how this side came out. I was smart enough to tie the inner metal directly to the upright first, then add the new braces. I have some work ahead of me inside the wheel well on the driver's side. Still, the front end is obviously much more solid now and I'm pretty much done with it for a while.
The guy in the picture is an upper shock mount for the rear. I went through a couple of designs for this, and this is the final version. The plate will be welded inside the wheel well and will help spread the load somewhat. The spacers on the inside of the mounting tabs help keep the tabs clear of the adjuster on the shock, allowing me to put a wider base on the tabs than I would otherwise.
entry 250 - tags: suspension
January 11, 2010 - A rear shock in place!
Very exciting. The place where I mounted the plate for the upper shock mount is well tied into the structure of the car and is very solid - although there is some carpet just on the other side at one point, which I got a little warmer than the designer intended. The mount on the axle is only tacked in place, but that's an easy thing to change. I have to pull the rear end out to put a lower mount on the driver's side.
The upper mount is positioned so the shock is almost bottomed out when the stock bumpstop - visible above the axle in this shot - is compressed and the other wheel is at full droop. Worst-case scenario, of course. But there's a problem. When I assembled everything, I discovered that I only had about an inch of droop travel at my expected normal ride height. I've been spending so much effort on making sure I have lots of compression travel, and with my 5" long shock travel I assumed I'd have good droop. Nope.
Maybe my worst-case scenario was a little too worst-case. I'll have to do quite a bit of surgery to the stock wheel well to make that happen. Heck, I knew that already. Still, I do have an option. AFCO sells a replacement upper rod end that's an inch longer than the ones I have. This would cut an inch of my compression travel (would it be missed?) and give me another inch of droop. We'll see how things work when the car hits the road. For the time being, I'm just happy that I have suspension on three corners now!
entry 251 - tags: suspension
January 13, 2010 - Good question.
Someone on the Grassroots Motorsports forum asked about the relative difficulty of building a car like my Seven or the MG. For those who don't want to go read the discussion on the forum (there are some good points from other folks to do with registration and the like), here's what I answered. Note - I don't usually refer to the Seven as a Locost because I didn't build the frame. But that's what it is. Warning, long!

Here's a point-by-point comparison.

The Locost is basically a clean sheet when it comes to packaging, and the frame is built to accommodate whatever powertrain will go inside. Before the first piece of metal is cut, there are no constraints. This can cause a problem for some people, as design paralysis can kick in But it does side-step some problems right from the start.

The MG, on the other hand, is heavily constrained. The new drivetrain has to fit into an existing package. In my case, I'm making dramatic changes to the car to build what I want to build, but I still have to fit everything into the body and deal with things like the pre-determined position of the fuel tank or the steering column. Of course, this also means I don't have to deal with problems like trying to figure out where to place and how to mount the fuel tank. But just think of the exhaust - on a Locost, you stick it out the side of the car. With the MG, it's going to have to go under the car and thread through the suspension.

The Locost is very simple. It's a car, distilled. There's nothing there that isn't required. This makes life easy.

The MG, not so much. It's expected to be a real car with a heater, a certain amount of sound and noise insulation and the like. Of course, most of the hard work has already been done - the windows roll up and down, it's carpeted, it has a heater and ventilation plumbing, etc. Some care is required to retain all this.

The Locost is built out of clean steel. The MG has 40-year-old undercoating. Yuk.

With the Locost, you're responsible for everything. Need fenders mounted to your wheels? Make a bracket. Need seats? Figure 'em out. Need a steering column, a fuel filler, a scuttle, etc - it's all you. You've got some design freedom, but nothing comes for free. You have to solve every single problem involved in designing a car. This is the biggest part of the work.

With the MG, I only have to deal with the parts I'm changing. I don't need to figure out how to hang doors, mount the headlights or deal with airflow management behind the dash. That's been done for me. This helps. Of course, it would have helped more if I hadn't tossed the stock suspension away!

So which is harder? From a problem-solving point of view I'm going to say the MG, due to the existing constraints. For example, I'm not only going to have to figure out a steering column, but I have to figure out how to make it work with the existing firewall and column mounting. But it's a pretty close race, and if I'd decided to do a more traditional 302 or Rover swap into the B - which would have retained the suspension front and rear - then it would have been the other way around. My MG is a pretty extreme makeover. It helps that I have the knowledge that I gained during the Locost build, I suspect, but it's difficult to quantify that as I always assume when looking back that I knew then what I know now.

Time is hard. I didn't build the Locost frame, and I was single then. Instead of building in my own garage living on my own, I'm building in a garage that's attached to the house I share with my wife. This means no late-night grinding and hammering. It also takes me longer to do simple things like make dinner! I'm going to estimate similar time overall.

Money? That's such a variable. I think it's actually going to be pretty close. I could have found a cheaper MG (heck, a free one found me recently that would have been a perfect starting point) but I also bought my Locost frame. I don't pay attention to the total costs, I don't want to know. I just try to do everything for the minimum cost to do it right.

In terms of skills, I'd put them at a wash. I'll have to do more fine bodywork on the MG (no rivets here) due to my need for flares, but overall the basic skillset of shaping and welding metal, wiring, plumbing and painting is the same. Had I found a different MG to start with, I expect rust repair would have been a new skill I'd have to learn. But it's just an application of the metal and body work.
entry 252
January 15, 2010 - A long day with not much actual progress.
I managed to cut out a bracket. Oooo!
Actually, I did quite a bit more than that, mostly planning. I was following a pickup this morning and noticed that the shocks were mounted very far inboard. I realized that this would give more wheel travel for a given amount shock travel, and that I had previously considered a slightly more inboard mounting point on the MG. Obviously I wouldn't want to go too far, as my coilover setup would put some pretty major bending loads on the rear end and the lessened shock travel would mean less precise damping. But would it make much of a difference?
So I dragged the rear end back off the workbench were it was set up to have the shock bracket mounted on the driver's side, and stuck it back under the car. A bit of rough measuring showed that my alternate setup would give me an extra 1/4" to 3/8" of droop. Nothing to be ashamed of for such a simple change, and it would also give me more room in the wheel wells. It would also drop the lower mounting point of the shock down considerably, about 1.5" closer to the ground.
However, while doing my measuring, I discovered I'd mis-measured last time and I really had 2" of droop travel from my expected ride height. I suspect I hadn't let the shock fully extend, these AFCO shocks don't have internal pressurization so you have to actually pull them open. If the damping is cranked up, that takes a significant amount of effort. Regardless of the cause, it appears I have nothing to worry about so I'll continue as planned. The rear end came back out and was reinstalled on the workbench.
While poking around back there, I started looking at other packaging concerns - specifically, the available space for a muffler. There isn't much. The layout of the MGB GT's truck is a little weird, though. There's a fairly tall flat floor. If you lift it up, you discover a cavernous hole that exists to house the spare tire and quite possibly enough tools to disassemble the car. If I move the fuel tank into this space, that opens up a huge amount of room for a muffler underneath. I could either move the existing tank without too much trouble or build my own new one with some baffling inside. Mounting the filler is going to be a bit more of a problem as it would then be about level with the tank, but I have an idea.
More work!
entry 253 - tags: packaging, suspension, fuel tank
January 17, 2010 - The new fender flares have arrived.
They're going to be much, much easier to work with than the originals. It's interesting to see just how similar the shapes are front and rear though.
entry 254 - tags: fenders, body
January 17, 2010 - Touchdown!
A bit of time cutting and welding, and suddenly I had full suspension on all four corners. Naturally, the only thing to do was to bolt on some wheels and drop the car to the ground. The spring rates (250 rear and 375 front) were chosen simply because they were handy, and the ride height was set to "no preload on the springs". It actually turned out pretty well after I dropped the nose down slightly!
When I tell someone about having the car sitting on its wheels, they don't seem to share my excitement. This car has a completely new suspension, not just a bolt-on setup! This is a huge step!
After having the car up in the air for so long, it looks much smaller sitting on the ground. Janel thought it looked like a Hot Wheels car with the wheels poking out of the wells.
Turns out my initial measurements for droop travel were accurate - there isn't much. I think the smart way to fix that would be to simply move the lower suspension mounting point up by an inch or so. Of course, I had the car a little tall today because I can't compress the rear suspension much without cutting the rear fenders. That'll happen soon enough, but I'll probably concentrate on the other big jobs first.
Less than an hour after touchdown, the car was in the air again. And I was dragging the engine hoist towards the car...
entry 255 - tags: suspension
January 20, 2010 - With the engine back in the car, I determined the final location of the big heavy parts.
In short - quite far back and nicely placed vertically. I'll have just over 5" of air under the sump at my expected ride height, but the hood closes all the way. The shifter is in just about exactly the stock location.
So the next thing to do was to build motor mounts. The passenger's side was straightforward enough, but the driver's side was a real challenge. The mount is extremely close to the steering column, enough that I'm going to have to weld the lowest universal joint to the shaft instead of bolting it on, as there isn't enough room for the bolt to clear the mount. I finally figured out how to put a motor mount bracket in there, but I don't think I can create the lower section until the engine is out.
I did check the clearance on those new headers I brought home. Nope, they won't fit. The passenger's side is good, but the driver's side is not. That steering column again. The headers are obviously from a car that is several inches wider than our little beastie. I can see the possibility of headers that require the removal of the steering column to install - I'll try to avoid that.

The transmission support will take the shape of a new crossmember - pictures to come. I need to make this removable so I can actually take the engine out of the car again, which made everything much more difficult. I'm almost there. This is a very satisfying stage of the build.
entry 256 - tags: motor mounts, packaging
January 20, 2010 - The transmission crossmember is finished.
Finally! It's upside down in the picture, in the car it steps up to reach the stock LS1 transmission mount. The bits on the end bolt in to captive nuts installed on the frame rails. Of course, I didn't have that set up ahead of time so I first had to weld the nuts on to a piece of 1x2" strap, cut two large 0.875" holes in each frame rail and then weld the strap on to the rails. The holes in the strap and the bracket are perfectly matched to the bolt size so there's no slop at all, which made positioning very important. I put the bolts in shear instead of tension for the simple reason that if they start to back off, my transmission won't start to sag downwards and eventually fall down.
The stud on the rubber bushing on the transmission is an inch long, which isn't long enough to protrude all the way through my mount. Thus the large hole in the middle, which is where the nut for the stud goes through along with a socket to tighten it up. Works like a charm, although I really need to deburr that hole to make it look better in pictures like this.
The raised middle section didn't end up being raised quite enough - the original measurements told me 0.75", and it looks as if 1.25" would have been more accurate after I decided the tail of the transmission needed to be slightly higher. Oh well, it's a good solid fit and it works well. Due to the close tolerances on the holes, it's actually a bit tough to install as the bolts won't thread into the holes unless the mount is perfectly positioned, but I'm willing to accept that particular tradeoff for a precise fit.
entry 257 - tags: transmission
January 22, 2010 - It's time to make sure I have room for some real brakes.
The car originally came with unboosted brakes, and long-time readers will remember that I rebuilt the master cylinder. That was back when I thought I'd be driving the car as a four-cylinder for a while. Ah, those were the days.
Purists, of course, claim the unassisted brakes are superior in almost every way. But those who are sensitive to subtle hints may have noticed that I'm not much of a purist. I have several cars with unassisted brakes (interestingly, they're all British or replicas thereof) but this car will have a fairly intense power/weight ratio, and I want power assist. Besides, the whole braking system has been replaced with Miata parts, and my rear discs take more pressure to operate than the previous drums.
The problem is twofold - first, there's not much room for a booster underhood. And secondly, the original pedals put the masters above the driver's feet - so there's simply no room for a booster at all in that setup. There are such things as remote boosters which are intriguing. A number of newer vans (and other packaging-challenged cars) also use a "hydroboost", which steals hydraulic pressure from the power steering pump for assist.
But there's an easier way. In 1974 or 75, MG added power assist to the MGB. And in order to do so, they used a very small brake booster, a master cylinder with an angled top to clear the hood, and a different pedal box that put the brake hydraulics in front of the pedal. And it's a simple bolt-in to the earlier cars - although most MG owners go the other way, installing the unassisted setup. I found a complete pedal box, booster and master on the MG Experience website and had it in my hands a week later.
The first trial installation showed that it's a perfect fit. The front outlet is fairly close to my shock tower mount, but a well-placed divot would take care of that. The rubber line that runs close to the booster is actually the vacuum line on the engine. It's just sitting there, I can easily route it with lots of room.
I need to do a bit of figuring with pedal ratios (looks like it's in the 4:1 range) and master cylinder sizes (0.75", apparently) and see what that does for my brake pedal travel. I may want a larger master, as the Miata has a similar (4.1:1) pedal ratio but runs a .875" master. I'll measure the MG one more carefully tomorrow. Luckily, mounting a Wilwood unit is fairly straightforward. So there may be no reason to put that dent in the sheetmetal anyhow.
First, I'll stick this setup in the bead blaster and make it all pretty!

I've been puzzling on the best way to package this for a while, looking at various booster combinations. But I'm really happy with this result. I think it's going to be very clean.
entry 258 - tags: brakes, hydraulics
January 24, 2010 - I love my bead blaster.
That's the pedal box for the boosted brakes on the right, with the unassisted setup on the right.
entry 259 - tags: brakes
January 24, 2010 - After a fair bit of calculation, I'm starting to figure out my brake options.
From my measurements, it looks like the MG brake pedal has a ratio of 4.48. That means that 100 lbs of pressure on the pedal is transformed into 448 lbs on the master cylinder. It also means that it takes 4.48" of pedal movement to move the master cylinder pushrod by 1". Basically, it's the same as a gear ratio. The Miata pedal has a ratio of 4.1 according to the manual.
I know the Miata setup pretty well, and the Targa Miata uses the hydraulics from a later Miata setup. The standard Miata master cylinder is a 7/8" unit, and the Sport master is 15/16".
As you can see from the picture, the stock MG master cylinder is 13/16".
So, based on pedal ratios and master cylinder sizes, I compared how much force on the pedal is needed to get 250 psi of line pressure. Why 500 psi? No reason, it's just a constant so I can get an idea of how the different setups would compare in feel for the same amount of braking. I also figured out how far the pedal would have to move in order to push 1 cubic inch of brake fluid, as the leverage ratios and hydraulic multiplication always trade off travel for effort. Here's what popped out of my spreadsheet:

  • MG pedal, MG master: 57.87 lbs, 4.32"

  • Miata standard setup: 73.3 lbs, 3.41"

  • Miata Sport setup: 84.2 lbs, 2.97"

  • MG pedal, 1" Wilwood master: 87.7 lbs, 2.85"



So no surprise here, the further you move the pedal the less you have to push on it. Simple leverage. And if you're doing these calculations at home, remember that it's a dual circuit system so you'll get half the pressure and twice the fluid flow as you would with a single circuit of the same size.
According to my calculations, a 15/16" master on the MG pedal (77 lbs, 3.25")would be pretty much right between the two Miata types. But the dual circuit remote reservoir master cylinder available from Wilwood is a pretty unusual piece, and only available in a 1" bore. I need the remote reservoirs to clear the hood, I believe. I do have a few other single circuit master cylinders I can use for test fitting for clearance.
Still, since Janel and I both prefer a nice firm pedal, I'll probably go with the Wilwood 1" setup.

But of course, there's a catch. The booster. All the calculations above give the numbers for an unassisted brake setup. The booster will multiply the force on the pedal to give more force at the master. If the booster has a 2:1 boost ratio, that means it would only take a bit less than 44 lbs of force on the pedal to generate my 500 psi of line pressure, instead of 87.7. And here's the problem. I don't know what the boost ratio of the MG booster is. The Miata one should be around 4.6 according to the manual.
So the end result is going to come down to trial and error, with a bias towards a too-firm pedal instead of a too-soft one.

This stuff is fun. I get to learn all sorts of things.
entry 260 - tags: brakes
January 24, 2010 - Sometimes, you have to walk away from a problem for a while.
I don't know why I didn't think of this - the Miata comes with either a 7/8" or a 15/16" master, depending on the application. It has a plastic reservoir that can be removed and turned into a remote setup. And while the bolt pattern isn't correct for the MG, its close enough that I think I could make it work.
I'm also going to make sure the Miata booster won't fit on the MG pedals. If it does, then life is very simple. I'll have a complete Miata brake system with a slightly different pedal ratio. I'll find out tomorrow.
entry 261 - tags: brakes
January 24, 2010 - Next challenge: the steering column.
I'm trying to deal with all of the major packaging problems right now. And this is a good one - the universal joint from the MG that bolts on to this column is so big I can't even slide it into place. It hits the head. As an added bonus, the shaft is a considerably larger diameter than the Miata one at the steering rack.
entry 262 - tags: steering, packaging
January 24, 2010 - The first possible solution I came up with to the steering column problem was my standard go-to option.
What about a Miata? So I grabbed a Miata column, stuck a wheel on it (I have at least three wheel adapters and a range of wheels that will fit) and started measuring. Turns out it's ridiculously good.
It doesn't look like in the picture, but the lower side of the bracket on the end of the Miata rack lines up with the location of the firewall on the MG. Easy alteration and the lower mount is done. The flat plate that serves as the upper bracket is actually in exactly the right place. Depending on the wheel adapter I use, the two holes on the Miata mounting plate are in the same place as the MG ones. Well, they're about 10mm closer together than on the MG. But this is a very solvable problem. The third mounting point would be easy to add. And the overall length is shorter, which will move that awkward U-joint further up.
entry 263 - tags: steering, packaging
January 25, 2010 - Just for fun, I checked the length of the lower section of the Miata column.
After all, it's designed to bolt directly into the steering rack. I couldn't believe the result. It's perfect. Not just "close", but bang on perfect. The universal joint tucks into the recessed spot in the firewall, and the rest of the column inside the car is in the correct spot. This could not be better, I really lucked out.
Inside the car, I can play with the final location of the wheel using my various adapters. I'll use the Miata combo switch (ie, stalks) to control the turn indicators, lights and - yet another bonus - the cruise control from the Camaro. I don't think it'll look too anachronistic in the MG interior, and the Miata parts both feel better than the MG ones and give me the controls I need instead of requiring a bunch of extra switches on the dash.
I still can't get over how well this works.
entry 264 - tags: steering, packaging
January 25, 2010 - Another shot of the proposed steering column routing.
It looks as if it'll be fairly simple to arch the exhaust out a bit and run the column between the header and the block.
entry 265 - tags: steering, exhaust
January 26, 2010 - So, while trying to figure out a few things about the MG booster, it was suggested to me that I try to fit the Miata booster.
As with everything else in this car, make it more like a Miata! Well, my initial reaction was concern that it would fit - the MG part is silver and the Miata one is black in the picture. There's nearly 2" of diameter difference involved.
But I had to try.
entry 266 - tags: brakes, packaging
January 26, 2010 - And voila!
Some light massaging of the inner fender with a 2 lb sledge (about the only part of the inner fender I haven't actually cut off by this point), a new bolt pattern on the pedal box and some clever twisting and turning of the assembly to get it into place, and there's my Miata brake booster installed in the MG.
In researching this, I found that there are actually three brake boosters that have been used over the years, with three different boost ratios. I'll be able to fine-tune my braking effort nicely. Now I just need to source a 15/16" master cylinder from a 2001-05 Miata. Easy enough.
There's just one problem with the fitment of the new booster.
entry 267 - tags: brakes
January 26, 2010 - The booster and the engine end up very close to each other.
Very close. That little port on the head is only about 1/4" from the edge of the booster. It's normally connected to vacuum line that runs from one head to the other, I suppose to prevent pressure buildup on one side.
I looked at a later LS1 and an LS3 in the shop, and I got bitten by the 1998 donor again. In 1999, the heads and valve covers were changed to a center bolt design instead of the peripheral bolt setup I have. This means I can't use a particular Edelbrock coil cover I thought would look great, but that's not important right now. On my engine, both valve covers are the same casting. The little port on the driver's side that's causing me problems is where the oil filler is placed on the other head. On later engines, the driver's side valve cover has a much stumpier protrusion for this port which would give me lots of clearance. This is not a big problem, I'll just whack it off and weld it up. If I decide to keep the connection from head-to-head, I have a few options. So it's not a show-stopper, it's just a bit more work. And it means I'll have to pull that valve cover off - easy to do, just something I was hoping to avoid.
Still, the final result is good. Other than a slightly different pedal ratio, I'm basically running a full Miata brake system. And I know Miata brake systems!
entry 268 - tags: brakes, packaging