Slow Car Fast
THE MG
November 28, 2010 - I changed out the rear springs to 225s earlier and took the car for a bit of a drive.
Good, although they're 8" long and don't have quite enough travel for my 5" rear shock travel. It's possible they could coil bind on a really hard hit. I'll keep them in for a bit of testing first, and if they get the nod I'll pick up some 10" ones.
I just swapped out the front springs from 375 to 300, because that's what I have in the garage! I'll drive the car tomorrow (weather permitting) and see how they feel.
I have to say, changing springs on this car is ridiculously easy. It only took 5 minutes to change both front springs. All I have to do is lift the car, pull the wheel, remove the external shock boot (attached by velcro), spin the perch down, unclip the upper perch, unbolt the top of the shock, pull the old spring off, drop the new one in and just reassemble. It sounds like a lot of steps when laid out like that, but it's very fast. No need for a spring compressor and only one bolt.
entry 487 - tags: suspension, springs
November 29, 2010 - The MG has caught some people's attention.
Specifically, it was featured as an LSx Oddity on LSX TV. That's pretty cool, and the car is making the rounds of various forums who normally wouldn't see it.
Unfortunately, it's also getting stripped of any context and so people seem to think they're looking at the final result. The chopped-up wheel arches, the wheels sticking out of the body, the battered paint - the term "redneck" has been flung. You know, if I thought this was the final result, I'd agree. But the car's made some huge strides even in the past two weeks, and when I start on the bodywork I think all will become clear.
entry 488
November 30, 2010 - A big adventure for the MG!
I drove the car to work today. Intake air temperatures of 25F tells me two things: the air filter location is picking up nice cold air and, and baby it's cold outside. The heater works but there are a few holes in the firewall for wiring and the like that let in a cool breeze.
The suspension is working quite nicely from a ride standpoint. The car is now absorbing bumps well and shows good composure. No word on how it handles yet, I'm withholding judgment there until all the wheels are pointing in the correct direction. But the car feels right. It has 300 lb front and 225 lb rear springs at the moment.
I took the interstate on the way in to see how the car deals with highway speeds. Answer: pretty darn well. No evil habits showed themselves at high velocities, up to 75 mph based on other traffic. There are a few rumbles through the body that I suspect might be the exhaust leaning up against the frame - there's one point where the piping is really, really close. A cleverly placed dent will solve that problem. I'll check the bottom of the car to see if there are any rub marks. I'm hoping that's what I was feeling, it didn't quite feel like mechanical vibration. The near-solid motor mounts were certainly adding a bit of buzz.
This was the first chance a number of my coworkers had to check out the car. Bill, my boss at Flyin' Miata, was impressed with the exhaust packaging and can't wait to drive the car. I asked him to wait until I had the alignment done. Lots of commenting on the packaging to make the engine fit. Adam stood to one side, looked at the wheel well and said "I can see the headers!"
So far, so good. Now, how will the drive home in the dark work out?
entry 489 - tags: testing
December 1, 2010 - Alignment time!
I took the car down to the local alignment shop where they know me pretty well. It's the sort of place where they're not really surprised when I show up with a V8 MGB. The car was a big hit, though. The guys there are the sort who can see past thinks like chopped up fenders and exposed wiring to see the coolness underneath.
So how did it fare? Well, we discovered that if I want less than 1.5 degrees of negative camber on the right front, the shock will hit the control arm. That can be fixed with a bit of grinding on the arm or a relocated bracket, so it's not a big deal. Besides, 1.5 degrees might be about right. When the car drove in, it had -3 degrees on one wheel! The only other problem report was that the Panhard bar is set to the minimum length and it needs to be very slightly shorter to center the axle. Right now, it's 0.27 degrees off. Interesting measurement, that, it's the angle from the center of the rear axle to the centerpoint of the two front wheels. Odd.
The final result is -1.5 degrees of camber, 5 degrees of caster and 0.04" of toe-in. I might remove the latter but that's easy to do at home. The rear, of course, is a solid axle so the alignment numbers are pretty boring. It had 0.27 degrees of thrust angle from my eyeball setup, not bad at all.
One nice thing to see what that my wheelbase is within 0.1" side to side. Looks like I managed to get those control arm brackets in the right place!
And of course, then there was a Lucas moment. The car refused to start. A bit of troubleshooting revealed that the PCM wasn't getting power but other switched circuits were. That's a fairly straightforward problem, as it's very simple wiring. A bit of poking and wiggling and I woke it up again. I suspect it was a bad crimp in one of the spade connectors, so when I got home I cut it off and installed another. This particular wire had been an early installation, and it's been yanked and pulled multiple times at a sharp angle over the course of the build. No harm done, that's the sort of thing you expect on a shakedown like this.

So, how does it feel? Well, I was mostly thinking "I'd better get home before that connection give me more trouble", but it does feel better. The steering still doesn't self-center very hard, so I'm going to check for friction in the column. But it does feel more planted. I'll get it on the highway tomorrow for some higher speeds to see.
entry 490 - tags: alignment, wiring
December 1, 2010 - So, with the wheels all properly located in the wheel wells, it's time to remove some of the redneck and install the fender flares.
These flares are from an original Rabbit. I have a set off some front fenders cut off a junkyard car, and a set of rear "rust repair" panels that are brand new. After trying the various flares on different corners of the car, I decided the best fit in the back was to use the Rabbit rear flares on the same side they'd be fitted to the Rabbit.
First, I cut the flares off the rest of the patch panel. Then I played with placement to get it to sit just right over the wheel, and finally marked the position.
entry 491 - tags: flares, body
December 1, 2010 - After the paint was removed from the fender area, the Rabbit part was tack-welded on.
I then reinstalled the wheel, dropped the car back down and double-checked placement.
Just look at how that fender fits the MG body. It's perfect.
entry 492 - tags: fender, body
December 1, 2010 - There's one problem with the flares, though.
They sit high enough on the body that they cross over the line where the stainless steel strakes run. This leaves a gap at the top of the flare where the body steps inwards. These fenders have a little curve where they meet up with the body, so before installing them I used a body hammer to remove the curve and flatten the profile of the flare in this area.
I am mounting these flares higher on the body than I've seen on another car - the only other car I've seen with the Rabbit flares. It could be that my ride height is lower, but aesthetically I'm happy with the placement.
entry 493 - tags: body, fender
December 1, 2010 - With the fender properly placed, I welded it on.
Lots of small spot welds to keep the heat under control. I'm really happy with how this turned out.
entry 494 - tags: fenders, flares, body
December 1, 2010 - The solution to the gap was a patch panel.
It's shown here on the other side, because that's where I managed to get a better picture! I used card stock to work out the shape, cut a carefully shaped patch out of the leftover patch panel sheetmetal and welded it in. A bit more attention with the flapper wheel on the grinder and a bit of prep work and it'll look nice and smooth. It also makes the fender flares look much bigger than before!
entry 495 - tags: fender, flares, body
December 1, 2010 - The new flares have a fairly big lip on the inside edge, typical for production cars.
Unfortunately, it means that my tires hit at full compression. So this lip has to go.
entry 496 - tags: body, flares, fenders
December 1, 2010 - The solution?
A fender roller. Now, I often get accused of having access to special tools due to the fact that I work at Flyin' Miata. And I have to admit that this is one of those situations. Not that a fender roller is all that exotic, but it's easy to just grab the one off the shelf at work instead of having to borrow it from someone.
The low-tech way to do this would involve a baseball bat or jack handle, of course. I've done that in the past, so I think I've paid my dues!
entry 497 - tags: fenders, flares, body, fender roller
December 1, 2010 - The roller is a pretty nice tool.
It allows you to slowly and carefully shape the fender, rolling that flat flange upwards so it gives more room without any visible changes. It's easier on an unpainted panel like this, of course, but I've made some fairly spectacular alterations to a couple of Miatas. In extreme cases, you can stretch the fender outwards for more space. I didn't have to do that here.
It might seem a little odd to build a custom fender and them immediately modify it like this, but it's part of getting the best fit.
So how's it look? Pictures will be forthcoming once I get the car out of the garage. Basically, the car's gone from looking pretty cool to just plain badass.
entry 498 - tags: fender roller, flares, fenders, body
December 2, 2010 - The final result!
I'll hit it with some black primer to protect the metal and make the shape blend into the body, but I'm really happy with the result.
entry 499 - tags: fenders, flares, body
December 2, 2010 - Another view from the front quarter.
Sorry about the exposure, the Colorado sun is pretty harsh for photography. I'll get some better ones later.
After some playing around yesterday, I decided that rear Rabbit flares (as seen on the rear of the MG) fit the front of the MG better than front Rabbit flares. Of course, I have a pair of junkyard front flares but no more rears. No worries, rabbitparts.com shipped me another set of patch panels yesterday and I should have them within a week. As a bonus, they're nice clean new metal like these instead of junkyard parts.
entry 500 - tags: body, fenders, flares
December 5, 2010 - I had time for some relatively quick and easy jobs this weekend, and I'm still waiting for the new set of flares to arrive.
So I started messing around with little trim pieces. First up was the tail lights. A few people had commented on how the older lights looked better. From pictures, I'd felt that was true for the convertible but not so much for the GT. But the 1969 parts car came with a set of the older ones, and I'd really come to appreciate the shape. So I swapped them over. Here, you can see one new old design light on the left and one old new design on the right.
entry 501 - tags: lights
December 5, 2010 - The rear end with the new lights.
Sharp eyes will also notice that I "shaved" the side markers as well (okay, I removed them and stuck a piece of black duct tape over the holes) and swapped the overriders for the older design. The 1972 ones have a rubber insert. Here's the "before" picture.
I'm really happy with the result. Janel described the older lights are more streamlined, and I think she's right on. They look much better. With all the changes, the car just looks cleaner from the rear. I actually had a set of new lenses for the previous taillights, but this is much nicer.
Of course, this light work wasn't without a certain amount of troubleshooting. The taillights weren't very well grounded, so I added a ground strap to make sure they worked consistently and well. A couple of dodgy bullet connectors also caused me to spend some time cleaning things up. I'll keep an eye on the behavior of those rear lights.
Sometimes it's nice to do the little things that make a satisfying difference. These sort of changes will make the whole car just work better, even if most people can't identify what was done.
entry 502 - tags: lights, wiring
December 5, 2010 - The messing about wasn't restricted to the rear.
In the front, I swapped the orange one-piece front lights for a set of older two-piece ones with clear lenses. This makes the whole front of the car monochrome with the exception of that MG badge, and again it cleans things up. The lights came with a set of white bulbs, but I installed a set of orange ones in the turn indicators to make them more visible when lit. The overriders were also changed out for the older ones. Again, it's a cleaner look than before.
The grille has been discussed before, a couple of years ago before I started on the engine conversion. It's a 1974 grille with a 1960's MG emblem, chosen because the black opening looks more aggressive than the old design to my eyes and because the newer emblem just looked cheap. Here's what the car looked like when we got it, with the overriders removed.
Less obvious is a set of new headlights. They're a set of European Bosch lights that put out a really nice pattern and let me run H4 bulbs. It's what a European MG would have, and the lighting is much better.
Again, not big changes. But ones that make me smile when I look at the car and will make it look better.
entry 503 - tags: lights
December 5, 2010 - Time to do some functional work.
I found what is likely a source of a fair bit of exhaust noise - the driver's side header outlet is leaning up against the footwell. Solidly enough to clear the paint off the footwell. So I pulled the header and exhaust pipe off and decided an effective fix would be a simple dent. A slot in the footwell, a few hammer blows and voila, lots of room. Given the shape of the footwell, it's unnoticeable from inside the car. I covered up the slots with seam sealer and I'll put it all together again shortly. I'm excited to see if this makes a big difference to the sound - I suspect it's where a fairly loud rumble/vibration at higher loads and highway cruise was coming from.
entry 504 - tags: exhaust
December 16, 2010 - I've been out of town for over a week, so the MG hasn't seen much action.
But the whole time I was gone, I was thinking about the fact that my new front fenders should be arriving. Less than 24 hours after getting home, I had the new fenders cut up and was doing test fitting.
And here's where I ran into a problem. Cars taper. They tend to be wider in the middle than the ends. Both the Rabbit and the MGB are like this. So the flares are slightly tapered to match. In the rear, I used the rear fenders on their intended sides and so the taper worked out well. But in the front, I had to flip the fender pieces - from a rear Rabbit fender - to the other side if I wanted the taper to work with me. Unfortunately, no matter how I played with them, I just couldn't get them to sit well on the original wheel cutout.
By flipping them back again - left fender on the left side - I was able to get the shape I wanted with a delicious little curl where the flare melts into the body of the car. That's a great detail on the original Rabbit that you can see with the bumpers pulled. But it meant that the flare was tapered the wrong way. The front of the wheel is left more exposed and there's a bit more flare on the trailing edge. Still, I thought it worked pretty well, so that's what I've done. We'll see what I think when it's all painted up and finished.
I did do a lot more trimming on the metal to deal with this and to mold the flares to the body. I usually find tin snips to be terribly frustrating devices but this turned out to be their destined use. A nice change from noisy power tools that are always trying to fling incandescent metal into my eyeballs.
entry 505 - tags: fenders, flares, body
December 16, 2010 - Just as in the rear, I had to add a filler piece to mate the flare to the body.
However, unlike the rear, it was trying to mate up to a fairly heavily curved fender. It looks a bit weird in the picture, but I think it'll look good when it's all painted.
I hope so anyhow.
entry 506 - tags: fenders, flares, body