|LIFE OF A GT
|December 17, 2010 - The best angle.|
I want to spend a bit more time walking around the car and getting a feel for how it looks (and learning to photograph it well!), but I'm happy with this. It almost looks as if it should have come from the factory this way, which was my goal. I can see a few things I'd change if I did it again on the fronts (especially now that I've learned a few things about fitting the metal) but that's just my reaction after spending a few days working on them. It's like the stripes on the Targa Miata - I'm not happy with how they flow on one corner or around the rear taillights, but nobody else has ever noticed.
To celebrate, we used the car for a bit of running around town including some grocery shopping. Naturally, my freshly-adjusted latch on the tailgate decided to get ornery and refused to open, so we had to load all the groceries in through the front doors. The car's still fairly loud, but I think I managed to solve the major vibration problem. We'll see when I get it on the interstate. Still have to fix that bit of stiction in the steering though...
entry 509 - tags: fenders, flares, body
|December 20, 2010 - It's been a busy few days.|
On Friday night, Janel and I took the MG out to run an errand or two - which turned into a big grocery shopping trip as well as other events. Of course, I had just adjusted the rear hatch and it refused to open again. So we had to load all the groceries in through the back seat. A tip for those who are planning to use an MGB GT for a station wagon - anything you put in the back is on clear display! Unless you stash it in the smuggler's hole underneath where the spare tire lives. Anyhow, a bit of lubrication when we got home and the problem was solved.
We also got a little hiccup when the engine died a block from home. It fired right up again, but that was a bit odd. My suspicion was low fuel.
The next morning, I jumped in the car to go to the opening of a new car museum close by the house. While sitting at a stop sign, the engine died again and would not restart. Banging on the bottom of the tank gave a very empty BONG, so my chase car (a Miata with a 480 hp LS3, of course) took off to get some fuel. My theory was that the fuel gauge (the original, on the original sender and wiring) wasn't quite calibrated right - or, as a safety margin, it never went completely to E because then it would appear to be not working!
The fuel arrived. That didn't work. Bill Cardell (the driver of the Miata) and I figured out the fuel pump wasn't running. And then it was - there must be a slightly dodgy connection in the system somewhere. I got to the museum and back without incident, but it really highlighted that I'm not just debugging my own work over the last two years, but also a 38-year-old British car that never really functioned fully when I first got it.
I'd like to point out that it's not a Lucas fuel pump, but a good Pierburg unit. Just before the Lucas jokes start...
The photo? I just like the way the car looks!
entry 510 - tags: debugging
|December 20, 2010 - I was asked for a side shot of the flares, showing how they fit over the wheels.|
And here it is.
The Lucas bullet connector between the new wiring and the fuel pump has been replaced. The culprit? I don't know. I also discovered that I never tightened down some of the connections on the main power bus, so it's possible that could be a culprit.
entry 511 - tags: body, fender, flares
|December 20, 2010 - Time to find out why the steering feels a bit odd.|
It doesn't have much self-centering and almost feels as if there's too much friction in the system somewhere. Step one: lift the front wheels off the ground and get a feel for it. Step two: start removing various components to find the friction. It's 100% Miata steering, so it should work well.
The first thing I pulled off was the steering wheel and compared it to a stock Miata unit. Bingo. Nice and free movement. Wow, that was easy to find. Experimentation with a few other wheels (yes, there are five on the workbench) traced the problem to an adapter that had slightly oversize splines. This let it slide too far down on the column and put a lot of pressure on the turn signal canceling mechanism.
entry 512 - tags: steering
|December 20, 2010 - The solution to the bad adapter was to replace it.|
This unit - of unknown origin - would bottom out a full 1/2" higher up on the column, avoiding the problem. But it was both too short and had the wrong bolt pattern for the wheel. So I cut both apart and welded them together using a piece of pipe as the spacer. Nice and solid, and with some attention to detail everything is parallel and centered. There's a rubber boot that slips over this so you can't see it.
A quick test drive showed a massive change in the steering feel, with good centering and lighter effort. Time well spent.
entry 513 - tags: steering
|December 20, 2010 - Okay, so now that I can steer, it's time to find out how fast I'm going.|
The T56 transmission puts out an electronic signal. Naturally, the MG speedo uses a mechanical drive. There's a solution to this that involves a little motor in a box that spins a speedometer cable to match an electrical signal, but it's fairly expensive. For less money, I found a Smiths programmable electronic speedometer! I've been waiting for this part to show up for well over a month now, it seems they're made to order by British craftsman and, well, it takes time. But it'll fit into the MG's instrument cluster better than any other gauge, right down to the font on the numbers. The black center on the needle is the biggest giveaway really. I had my choice between 140 or 170 mph ranges, and I figured the 140 would be easier to read in the sane ranges - and above 140, I need to keep my eyes on the road!
When I went to hook it up, I found another advantage to using a Smiths part. They still use the same Lucas wire colors! Switched power is green, instrument lighting is red with a white stripe - makes it easy. But I did have a bit of trouble.
The GM engine computer (PCM) puts out a digital signal to run the factory speedometer. So that's easy, just plug it into the input on the speedo and away we go. Umm, no. With the rear end up on jackstands, I ran the car in gear and nothing happened. I tried the "low voltage" setting and nothing.
A bit of research on LS1Tech.com revealed that the PCM puts out a square wave signal that doesn't always play well with aftermarket speedos. The solution is to pull the signal right off the transmission. Okay, that's easy enough. I spliced into the transmission VSS signal and tried again.
This time, the speedometer woke up but it was acting odd. It would pin, or just hover mid-range but not consistently. Finally, I discovered that by letting the car idle in first gear I could get a 70 mph reading. According to the OBD-II reader, the PCM thought I was going 7 mph. So my calibration was off by an order of magnitude!
I quickly set up the speedo to count 40,000 pulses per mile and it settled right down. It's still not properly calibrated (what would be the odds?) but it's in the ballpark now. I just need to check some numbers, do the math and input the proper calibration. Getting closer...
entry 514 - tags: instruments, speedometer
|December 20, 2010 - While the dash is out to work on the speedometer and other wiring, I've decided to remove the crappy tan paint on some of the parts.|
Most of the interior of the car was painted pretty well, but the dash itself hasn't weathered well. It's cracked on top too. The eventual plan is to recover it with fresh vinyl (or a metal dash if I can hunt down all the parts), but in the meantime I want to work with what I have.
These dash vents are no longer available. But a few minutes in the bead blaster brought them back from ugly to original!
entry 515 - tags: interior
|December 21, 2010 - A peek at the dashboard.|
It used to be a very shabby looking thing, it's looking much better now! Not exactly concours-ready - my technique of dealing with a crack above the speedometer was to put some black duct tape over top before painting - but it's worlds better. You can see dusty hand prints above the tach, the paint job isn't as patchy as it looks in the picture.
Although looking at that old shot of the interior, I see I have the location of some of the lights in the wrong place - the right turn indicator and the alternator light seem to have traded spots. That'll be a bit of a pain to change now, as I took a special effort to make sure they're properly anchored!
entry 516 - tags: dash, interior
|December 21, 2010 - Time to wire up the wipers.|
This should be straightforward, right? Well, no. Things started off easily enough, with one wire for low speed and one for high speed. I'm not exactly sure how to duplicate the intermittent setting, but that's no big deal.
But the Lucas wipers have an extra wire that is for the parking function, to return the wipers to home base if you turn them off halfway through a stroke. It's a 12v signal that is fed back through the low-speed circuit until the wipers are parked. I've been inside a Lucas wiper motor and it's a reasonably intelligent way of doing things mechanically in my opinion, but the problem comes from the fact that there's some switching that needs to be done inside the wiper switch. My Miata wiper switch doesn't have this internal logic. So I need to find some way to have the park wire connected to the low speed wire when the wipers are off, and disconnected when they're on. That's easy enough to do with a relay...except for the fact that I have to have the high speed setting do the same thing.
Finally, after a bit of scratching around, I figured a way to do it with a relay and a couple of diodes, without passing the load from the wipers through the diodes. Out came the soldering iron and it all went together well. There's still one odd behavior, the wipers move fairly slowly in "park" mode even though they're seeing full voltage and theoretically full amps. I'm not sure what's happening there, as I'm pretty sure they worked well before the relay went in. I'll revisit it tomorrow to see what's going on.
I did manage to get the squirter working today, and discovered that it's aimed in completely the wrong direction much to my amusement. As a bonus, the Miata wiper switch includes some logic that swipes the wipers three times after you trigger the washer. Excellent.
Oh, and horns now work as well. Meep meep!
entry 517 - tags: wipers, electrics
|December 22, 2010 - These center vents are supposed to have a chrome lip on them.|
At least, I think they are based on checking a lot of photos online. I decided to add one using model paint and a steady hand. Okay, it was aluminum and not silver, but it does the job. And it was a nice relaxing 20 minutes to paint the two vents and the escutcheon that surrounds them.
That's a heck of a word, escutcheon. But according to Moss Motors, that's what the goofy thing is called.
entry 518 - tags: interior
|December 22, 2010 - Lots of detail work on the car today.|
While the dash was out, I cleaned up a bunch of wiring, added sound deadening behind the dash (you can see some peeking through the glovebox), refinished a few switches, removed the radio antenna and generally cleaned things up. One of the things I did was repaint the panel in front of the dashboard black, and bead blased and painted the defroster vents in silver. I like how that looks. I also swapped the a-pillar trim for the black set off the parts car. All just little things, but it's making the interior look good instead of rough. There's still a lot to do, of course, but it's much more respectable now.
The switch on the far left of the dashboard is the "brake check" switch. I no longer have that function available to me, and I'm not sure what to do with it. The shape of the switch is like no other on the car, so I can't substitute a different on in its place. Right now, it's just blanked off.
entry 519 - tags: interior
|December 22, 2010 - The cleanup also spread under the hood.|
I'm starting to corral the wiring somewhat and bundling it into small harnesses, but I'm going to leave everything accessible until I've done a bit more debugging. Still, it looks better.
The two big hoses in this photo are for the heater. I've strapped them together with velcro strips. It looks pretty good and can be quickly removed and replaced. I'm also using the same stuff under the dash to hold wiring harnesses in place. You can buy rolls of it at Harbor Freight.
entry 520 - tags: wiring
|December 23, 2010 - The car is now completely assembled and all the debris has been vacuumed out of the interior.|
It's certainly not done, but it does look respectable. Before I started, the crack on the top of the dash was barely noticeable with all the other problems. But now the interior looks good, the piece of black tape I just slapped over top is very obvious. Oh well, it's only a temporary fix. One nice touch is that I managed to fit the reset/programming button in where the old choke cable went.
So of course, I took it for a drive. The speedo is reading fast, so I don't have it calibrated correctly yet. A call to Jeremy at Flyin' Miata reveals that the T56 has a 17-tooth trigger wheel on the output shaft, so I'm seeing 17 pulses per driveshaft revolution. Okay, now I can calculate the correct pulses per mile. I had 40,000 in there as a rough guess, looks like it should be 52,209 with my current tire diameter.
The car's quieter. Not exactly a Lexus, but more manageable. As I lay more carpet down in the footwells, it will improve. I think I've also missed some spots under the rear deck, and I may try some rubber motor mounts eventually. But it's pretty good. The new wheel position is a step up, I'm happy with that.
The car is certainly not sorted out from a suspension standpoint yet, though. I'm not sure how much of what I'm feeling is a very high amount of unsprung weight in the rear with that live axle - a 2200 lb car with the rear end from a small truck is certainly hurting in that regard. I think I need a bit more rebound damping on the front shocks, and I should probably start looking at fitting some sway bars. I also have some Falken Azenis 215 tires on the car which have very, very stiff sidewalls on them. There's a set of 615s in the garage ready to go on, but it is really tempting to swap in some wider 15" wheels and a more compliant tire. That means spending a big chunk of change, though, so I'll probably put that off for a while.
While filling up the gas tank, I got in a conversation with a few other guys and ended up popping the hood. I suspect this will become a fairly common occurrence...
entry 521 - tags: testing
|December 24, 2010 - Janel and I took the MG for some last-minute shopping.|
It was kind of fun, the car's enough of a "real car" we can do this now. It's definitely quieter and Janel strongly approves of the new interior look.
Unfortunately, in some stop-and-go traffic trying to get in and out of the grocery store, the car got pretty hot. I didn't hear the fans kick in, even though it momentarily got hot enough that both should have been spinning away. All of my other testing has been at higher speeds and cooler temperatures. I'm going to have to look in to this.
It was by far the coolest looking car in the parking lot, though.
entry 522 - tags: cooling
|December 26, 2010 - A (poor) shot of the complete dashboard.|
Quite a change from the original look. The overspray on the carpet isn't really noticeable in person, you only see it when it's all lit up with the flash.
There hasn't been any major work on the car in the last few days, I've just been driving it. The defroster got a test on Christmas night when we had to head home after dinner, and it passed. I still need to work on sound levels coming from the back of the car, but a bit more of my silver cladding should help out there. I suspect that this would not be a problem in one of the convertibles, but the coupe body does provide a nice resonance chamber at around 1500 rpm. Still, I've been enjoying it quite a bit so far. The speedo works well and seems to be accurate, the dash lighting is about as good as could be expected and overall the car is working fairly well. The new Bosch H4 headlights I installed put out ridiculous amounts of light, just as I'd hoped.
Just because it's that time of year, I took a look back to see what I was doing around this time in the past. A year ago, I drove the Camaro into the garage for the final time. Two years ago, we decided to disassemble the interior. And this year we used the car to drive to Christmas dinner. I'd call that progress!
entry 523 - tags: interior, testing, looking back
|December 26, 2010 - I decided it would be a quick and easy thing to check the fans out by just grounding one of the wires on the relay.|
I tried it...and nothing. A bit of probing with the test light revealed there was no power at the relays - and a check at the fusebox showed two blown 20A fuses, one for each fan.
Looking at the fan ratings, they're supposed to pull around 13-13.5A. But that's continuous running. I don't have the specs for a startup draw on these particular fans, but one other Spal I've used in the past has a continuous draw of 12.5A and a startup draw of 18A. So it's quite possible that my fuses simply weren't up to the task. The wiring could certainly take it, so I'll just drop in a couple of 25 or 30A fuses and see what happens.
entry 524 - tags: fans, wiring
|December 31, 2010 - I was out of town for a while, but the little brown elves brought me some presents!|
While driving the MG and working on the interior, I've been keeping a list of bits and pieces that it needs. The mirror is about the most exciting part - that's an earlier mirror that matches the driver's side one off the parts car. It's much nicer looking than the ones that came on the car, gives better visibility and lets me open the vent window all the way. Seems like an improvement!
The other parts are more prosaic. New wiper blades, a seal for the "fresh air door" on the firewall that I don't think will fully close anyhow, light bulbs, etc. Not exotic, but enough to make the car a bit nicer inside.
There's also that Innovate box. That's a pretty cool toy - more on it later.
|January 3, 2011 - Air time!|
I drove the MG to work today. This let me check out some of the new sound proofing and generally play with the car. More importantly, it gave me a chance to put the car in the air and take a good look at the underside from a bit of a distance, not from the distance you get using a creeper and jackstands.
Looks pretty good underneath, actually. The exhaust is very clear in this photo, but you can also see the new structure under the front of the car. The original frame rails (or the reasonable facsimile thereof found in the unibody) are cut off at an angle just aft of the control arms. The big new 2x4 box section runs from the transmission support forward, and everything ahead of those cut frame rails is new. The tape holding the heat shielding to the driver's footwell failed on the way to work, so it's missing here.
It's funny, the engine looks so small from this angle. That oil pan is tucked up behind an impact bar and should be very well protected.
entry 526 - tags: underneath
|January 3, 2011 - Here's the view from the rear.|
The tight packaging for the mufflers is pretty evident - in fact, that black mark on the right muffler is the insulation from the fuel level wire before I put some heat shielding on it! The new frame members running forward from the trailing arm mounts aren't very visible, but the arms of the lift are lifting from there.
The inspection did reveal a few things. There are a few wires that need to be wrapped up mostly for appearances sake. That fuel level sender wire is still awfully close. The fuel line and main power line also run pretty close to the exhaust (hard to avoid given the giant X!) and really should have some extra heat shielding just in case. But it's pretty good overall.
One thing did come to my attention. The pinion angle seemed a bit off, with the nose of the diff higher than I think it should be. The alignment shop set it, but either the adjustment shifted because the lock nuts weren't tight - they weren't - or they have a different idea of what it should be. The angles of this setup could very well be the reason I'm getting a bit of vibration in the car. Not a shaking, more of a deep rumble that could be the stiff motor mounts, exhaust noise or drivetrain vibration. So I dropped the nose down a bit and we'll see how it works on the drive home. Not tonight, though - a surprise snowstorm marooned the car at work and I went home in a stock 1992 Miata. Regular readers will remember I did almost exactly the same thing two years ago in the Camaro!
entry 527 - tags: snow, pinion, underneath
|January 3, 2011 - The newest toy.|
I picked up an Innovate OT-2 over the holidays. It's an OBD-II scanner with a bit of a difference. It packs a little wireless transmitter that can talk to an iPod Touch or an iPhone, allowing the iPod to display real-time data from the car, datalog it, read codes, give efficiency information or even simulate a dyno run. It's pretty cool stuff. I need to recalibrate my engine computer for the MG's tire diameter instead of the Camaro's so some of the readouts are accurate, but it's nice to be able to monitor the car so closely nd then just slip the screen into my pocket when I'm done.
Not many 1972 MGs can talk to an iPod!
entry 528 - tags: innovate OT-2, ipod